Poweredge 1955 chassis manual

Page Updating The Powerconnect Switch Module Firmware The startup configuration is stored in the non-volatile memory of the switch module and is loaded into the running configuration which is kept in the RAM each time the module boots.

For detailed information on the Cisco Catalyst Blade Switch , see the documentation that shipped with the module or on support.

Page 34 General System Configuration The slot number is determined by the slot number which a server module occupies. This leaves you in a free state, with no server module selected. The status flag on your desktop, if active, displays Free. Page Changing The Display Behavior 4 In the Scan Time box, type the number of seconds from 3 to 99 of desired time before the scan moves to the next server module in the sequence. To remove a server module from the Scan list: 1 In the Scan dialog box, click to disable the check box next to a server module to be removed.

Passwords require 5 to 12 characters and must include at least one letter and one number. Passwords are also case sensitive. Page 43 To remove password protection from your console: 1 In the Main dialog box, click Setup - Security.

Leave the box blank. Table Page Using Virtual Media Adjusting the Video Quality The Viewer Application provides video adjustments that allow you to optimize the video for the best possible view. To adjust the video quality, perform the following steps: 1 At the bottom of the Viewer Application window, click Calibrate.

Page 48 3 To access a server from the list of servers, click the button that represents the server you would like to view.

If you are already connected to another server, first disconnect from that server by clicking Detach at the bottom of the display. Using the virtual drives from within Windows is similar to using your physical drives. When you connect to the media at a management station, the media is available at the system by simply clicking the drive and browsing its content.

Dell Inc. Autres documents utiles Configuration initiale. Page 54 Configuration du commutateur KVM This arrangement continues with the so Dell's offering is very similar in many ways to the Fujitsu Siemens BX S2. There are no differences with the chassis so you get the same number of blade slots plus power and cooling arrangements. Four expansion slots are provided at the rear and Dell also offers an extensive range of modules.

The PowerConnect M switch blade provides sixteen Gigabit ports with ten internal ports linked to the chassis backplane and six presented to the outside world. Two of these allow the blade's dual Gigabit ports to be routed through to different switch modules for redundancy. Two more bays are provided for another pair of PowerConnect M switch blades but to use these you'll need to install an extra dual-port Gigabit Ethernet daughtercard on each server blade.

Dell also offers a TopSpin Infiniband card as well. The latest blade offerings are far fewer than those available for the BX as Dell has only one new server module that supports Series and processors.

There's room for a couple of hot-swap 2. Its fervent commitment to Intel has also boxed it into a corner as it currently has no Opteron blades whereas HP, IBM and Fujitsu Siemens all offer extensive support with the later capable of delivering a remarkable way Opteron blade. Installation of the is fairly straightforward which is just as well as Dell's documentation is truly a mess as you get one generic disk covering every product it's ever made.

Consequently, we found it a real pain having to constantly swap through a multitude of manuals when configuring the chassis, the KVM module, the remote management controller, the switch modules and the server blades.

In the configuration guide you can see how to access it with a serial cable. For the whole process there is another reference to the appropriate guide. You need to confirm that it has a DRAC module and identify which type it is. Documentation at the link below will tell you the various ways to get console access dependent on which module you have.

Most of the new ones can plug into KVM over ethernet switches. It simply had to be popped out and back in to get it going again which you can do while the chassis is running. Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams? Learn more. Asked 10 years, 5 months ago. Active 10 years, 5 months ago.

Viewed 7k times. Any suggestions? Improve this question. Tips for Adding a Web Browser Interface. Required and Recommended Blade Chassis Configurations.