Baja sportub 1050 manual

Press this key once to activate the low speed of the pump, press the key a second time to activate high speed and pressing it a third time will turn the pump off. These cords have internal illumination to let you know that power is being supplied to the components connected to them. This is a helpful troubleshooting feature should a problem with a component arise. The Nature 2 purification system is only recommended for personal use or family spa installations. With normal use, this filter should be removed a minimum of once every 30 days, or anytime you notice an appreciable decrease of the flow from the spa jets.

Page Spa Cabinet Instructions - Attach a garden hose to threads. There should be a slow but steady flow of water which originates from the gravity drain located in bottom of the Baja spa. Component s not plugged in - Plug in components.

These messages will be helpful when communicating with your local dealer or qualified technician if a problem should arise. Page 18 nOteS Baja Model has 51 therapy jets and 27 LED lights and deep seats in an 88" square spa x 38" deep. Model has the same dimensions, but with 50 therapy jets and a lounge seat. See all of our spa parts or enter the part number or item in the search box.

Browse by categories and subcategories in the left Category menu. If you are searching in the search box above using a part number that has hyphens, only search on one part of the number - like the last 4 numbers for a refined search. Visit links above to specific sections of the website to narrow down your search or see the main section of the part type you need such as control panels , spa heaters , pillows ,or filters. Enter Baja and a word describing the part needed into the Search Box above such as Baja heater.

Or see the spa parts store for all parts. Shoot us an email to support hottuboutpost. Have a question about a particular item? We will answer it fast. Note: Since Baja spas is no longer in business, serial number information will not help in finding replacement parts. Some parts have numbers on them which can provide a helpful clue.

Hot Tub Outpost is an independent business entity and is not an agent or affiliate of Baja Spas. Hot Tub Parts All Misc. Also includes the sensor. Includes light cord on other side of pack. The Command Center Sportub spa pack is complete with 15 inch heater Another view of the complete spa pack you get including the control system, heater, sensor and light cable.

BAJA spa pack You may also need a control panel which includes the spa overlay Warranty Information Manufacturer's Warranty.

Add to Cart. Quick view. Push pin for Baja Spa pillows. This is for one. This is the original replacement control panel for Baja Spas Sportub. The generic button layout overlay is also included.

The second press of the button will turn the light off. Press and hold this button to increase or decrease the desired temperature setting. The desired temperature setting will remain in the display box for 5 seconds as confirmation of the new setting. After 5 seconds, the display will show the current water temperature.

Note: The temperature program indicator will appear to indicate that the temperature in the display is the desired programmed temperature and not the actual water temperature. Note: A power outage to the system will erase any programmed settings.

If a power outage should occur, it will then be necessary to re-program the system. Filtering default is minutes, twice a day. Temperature default is degrees. The primary filter cycle will occur in 24 hours and run for min. This will repeat every 24 hours. The freeze protection mode is available if required. The circulation pump system will only turn off when the spa temperature exceeds 4 four degrees above the actual temperature set point.

Baja Spas also added other factory filtration modes and conveniences: Purge Mode: Everyday at approximately Noon, the booster pump will operate for a few minutes to stir up the spa water through the entire system. Smart Summer Mode: In high heat climate areas, Baja Spas circulation filtration system will automatically perform 2 special filter cycles that run at AM and PM respectively for 2 hours each to provide filtration and ozonation.

Simply step away from the spa for 2 minutes and the controls will automatically reset themselves. Changing these modes will alter the factory preset settings. The Nature 2 purification system, is only recommended for personal use or family spa installation. It is very important to maintain proper PH levels between 7. Note: See Page 13 for cleaning instructions before removing filter. Pull tab and turn lock ring counterclockwise. Remove filter lid and cartridge.

Replace components only with identical components. Baja Extreme Sound System controls should not be operated while inside the spa. These units are not provided with an outdoor antennae. If provided, it should be installed in accordance with Article of the National Electrical Code. Do not service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards.

Refer all servicing to qualified service personnel. The unit should be subjected to periodic routine maintenance once every quarter to make sure the at the unit is operating properly. Insert bolts and tighten securely. Install corner posts pay attention to "up" arrows to side panels, then small panels to each corner post around spa using panel bolts and bolt driver.

Completed Baja spa. Discard black cabinet plug and install drain thru hole and secure back nut. Place panel in place, making sure there are no crimps in line. Secure valve to cabinet. Re-attach clear hose completely over barbs and re-secure with clamp. Complete cabinet installation. Simply remove the drain cap. Attach a garden hose to threads. Turn front face counter-clockwise and pull outwards.

There should be a slow but steady flow of water which originates from the gravity drain located in bottom of the Baja spa. With normal use, this filter should be removed a minimum of once every 30 days, or anytime you notice an appreciable decrease of the flow from the spa jets. You should take time to clean the filter. It is suggested that the cabinet be treated annually with an additional coat of stain for maximum weather protection. Contact your Baja Spa Retailer for advice on which stain and oil work best in your area.

More frequent draining may be required depending on usage. The spa should also be drained if it is not going to be used for a long period. An empty spa MUST be covered. Direct sunlight on the acrylic surface can cause severe damage or blemishing of the acrylic spa surface, and can result in the voiding of the spa surface warranty.

Turn off the main circuit breaker or disconnect panel. Attach a garden hose to the drain hose bib, and then open hose bib allowing the water to drain from the spa by gravity. For complete draining, place outlet end of hose below bottom of spa. Your insulated cover can be cleaned with a non-abrasive household cleaner. A non silicone based vinyl restorer will help protect the surface from sun damage.